No Products in the Cart
| Filtration Media | Inorganic Microfibers 25 µm |
| Media type | Inorganic Microfibers |
| Filtration Rating | 25 µm |
| Flow direction | In-Out |
| Total Height | 480 mm (18 7/8") |
| Largest Inner Diameter | 92 mm (3 5/8") |
| Smallest Inner Diameter | 10.3 mm (13/32") |
| Largest Outer Diameter | 126 mm (4 31/32") |
| Stat. HS-Code | 84149000 |
| Country of Manufacture | China |
| Brand | Code |
|---|---|
| Airfil | AFPOVL44 |
| Baldwin | PT9306MPG |
| CIFA | 909881 |
| CIFA | 910101 |
| CIFA | K000910101 |
| Digoema | DGMH8CCC25 |
| Donaldson | CRS49003 |
| Donaldson | P172468 |
| Fai Filtri | R-630-4-A25-A |
| Fairey Arlon | TXW8C20 |
| Fairey Arlon | TXW8C20B |
| Fairey Arlon | TXW8CA25 |
| Fairey Arlon | TXW8CCC25 |
| Fairey Arlon | TXW8CGDL20 |
| Finn Filter | FC1099F025BS |
| Finn Filter | FC1099Q020BS |
| Finn Filter | FFPAVL1109925ABS |
| Fleetguard | HF7991 |
| Furukawa | 3000380023H1 |
| Ikron | HEK0840480ASFG025B |
| Ikron | HHC01590 |
| Johnson Controls | 1517015 |
| Mahle | TXW8CRN2025 |
| Omt | HR6304HN |
| Oxfil | HF.9428 |
| Parker Parfit | 937800Q |
| Parker Parfit | 943961Q |
| Parker Parfit | FC1099Q025BS |
| Parker Parfit | PR4421 |
| Sacmi | 5673036 |
| Sacmi | 5673036001 |
| Sofima (UFI) | CRC340FV1 |
| Sofima (UFI) | ERF34NFD |
| Sotras | SH8054 |
| Spare Part Mart | SPM-HYD-1867 |
| ST Separat Tech | ST1199 |
| ST Separat Tech | ST7991 |
| Uniflux | XH354 |
| Westfalia | 4164548 |
| Woodgate | WGTW8CCC25 |
We check what other aftermarket sellers charge for this same part. Their prices on the date we checked:
| Seller | Price | Checked |
|---|---|---|
| SONA Filtration | USD 86.71 | 6 Oct 2026 |
| eBay (2 aftermarket sellers) | USD 97.64 to 115.94 | 6 Oct 2026 |
| Spare Part Mart | USD 62.28 | Today |
Our price of USD 62.28 is 28% to 46% less than these sellers.
Found this part cheaper somewhere else? Send us the listing and we will beat it by 5% under our Price Beat Guarantee. Every order is also covered by our 30 day money back guarantee.
Dusty or dirty operating environments
When equipment runs on construction sites, in quarries, or in agricultural fields, airborne dust and grit constantly challenge the hydraulic system. The 25 µm inorganic microfibre media traps these hard particles early, helping prevent scoring of pumps and valves and extending component life in high-contamination conditions.
Continuous-duty production machinery
Hydraulic systems that run around the clock, such as in manufacturing presses or injection moulding, accumulate wear debris rapidly. Using this filter as a routine service item maintains consistent fluid cleanliness, reducing unscheduled downtime and keeping product quality steady.
Fleet maintenance consolidation
If your operation runs mixed-brand machinery that all share this common filter form factor, stocking a single aftermarket part number simplifies inventory. This filter cross-references to multiple OEM part numbers, lowering storage costs and avoiding confusion during service intervals.
Critical asset longevity programmes
For expensive capital equipment where a hydraulic failure risks high repair bills, this filter serves as a proactive defence. Its high-capacity microfiber media holds more contaminant than basic cellulose alternatives, supporting extended drain intervals and helping delay major overhauls.
This filter is a dimensional match for a wide range of cross-referenced filters from brands such as Donaldson, Mahle, Baldwin, Parker Parfit and others. Verify that your current element has the same key measurements: 480 mm overall height, largest outer diameter 126 mm, largest inner diameter 92 mm, and small end inner diameter 10.3 mm. As long as those dimensions correspond, the filter will fit the housing and seal correctly.
This element uses inorganic microfibre media with a verified 25 µm rating. It is engineered to trap metal wear particles, silica dust, and other solid contaminants larger than 25 microns, which are the primary cause of lapping, erosion, and spool binding in hydraulic components. The synthetic microfibre construction provides high dirt-holding capacity while maintaining low flow resistance.
The filter does not have a threaded centre spud. It relies on its inner diameter dimensions for location and sealing: the large end inner diameter is 92 mm, and the small end inner diameter is 10.3 mm. End seals typically sit inside these bores against the housing standpipe and bowl. Always cross-check these figures with your original part to confirm compatibility, as no separate thread specification applies.
No, this filter is an aftermarket replacement built to the original dimensions and ratings for fit, form, and filtration efficiency. It is not manufactured by the original equipment brands. You receive the same filtration performance and dimensional compatibility at a fraction of the genuine part cost, backed by our 30-day money-back guarantee.
First, relieve all pressure in the hydraulic system and follow lockout procedures. Remove the filter housing bowl, take out the old element, and clean the bowl and sealing surfaces. Lubricate the new filter's seals with clean hydraulic oil, place it into the housing ensuring the flow direction arrow (IN-OUT) matches the system, then reassemble and torque to the housing manufacturer's specification. Always inspect for leaks upon start-up.
We ship worldwide with full tracking. Every SPM filter is covered by a 30-day money-back guarantee and our price-beat guarantee. If you find a lower advertised price elsewhere or if the part does not perform as expected within 30 days, we will make it right.
Prices depend on your ZIP or postcode.
Live rates for the quantity selected, delivered to your door. Confirmed at checkout.
Drop your email below and the code is yours.
We will also tell you when that part is due again. A couple of emails a month, and you can stop them from any one of them.
WELCOME10
Use it on your first order. Check your email and confirm the address so we can send you the reminders too.
