No Products in the Cart
A pack of 10 copper D32 high speed laser cutting nozzles in the Raytools D32-H15-M14 format: 32 mm outer diameter, 15 mm height and an M14 thread, with the stepped high speed tip Raytools uses on its 120GJT25xx single layer and 120GJT16xx / 36xx double layer high speed nozzles. Each bore is listed against its Raytools high speed part number below.
Machined from copper with a concentric bore. Single layer for oxygen cutting of carbon steel, double layer for nitrogen or air cutting of stainless steel and aluminium. Bores from 0.8 mm to 6.0 mm.
Sold in packs of 10, all the same layer and bore.
| Pack Quantity | 10 nozzles, all the same layer and bore |
| Profile | High speed stepped tip |
| Outer Diameter | 32 mm (1 1/4") |
| Height | 15 mm (19/32") |
| Thread | M14 |
| Material | Copper (high conductivity) |
| Layer | single layer or double layer |
| Bore Sizes | 0.8 mm to 6 mm (16 sizes) |
| Part Numbers | Raytools 120GJT0508, 120GJT0510, 120GJT0512 and more (see table) |
Raytools cutting heads
Heads that take the D32-H15-M14 standard nozzle on the D32-H12-M14 ceramic (Raytools 120274100B). Check the nozzle currently fitted if unsure.
Fiber laser machines fitted with these heads
Fits these machines where they run a Raytools head that takes the D32 nozzle.
| Bore | Double LayerRaytools no. (SPM no.) | Single LayerRaytools no. (SPM no.) |
|---|---|---|
| 1.2 mm | 120GJT1612(SPM-LAS-2118-D12) | Not stocked |
| 1.5 mm | 120GJT1615(SPM-LAS-2118-D15) | Not stocked |
| 2.5 mm | 120GJT3625(SPM-LAS-2118-D25) | 120GJT2525(SPM-LAS-2118-S25) |
| 3.0 mm | Not stocked | 120GJT2530(SPM-LAS-2118-S30) |
| 3.5 mm | 120GJT3635(SPM-LAS-2118-D35) | 120GJT2535(SPM-LAS-2118-S35) |
| 4.0 mm | 120GJT3640(SPM-LAS-2118-D40) | Not stocked |
| 4.5 mm | 120GJT3645(SPM-LAS-2118-D45) | 120GJT2545(SPM-LAS-2118-S45) |
| 5.0 mm | 120GJT3650(SPM-LAS-2118-D50) | 120GJT2550(SPM-LAS-2118-S50) |
Carbon steel, oxygen
Use single layer nozzles. Small bores (0.8 to 1.2 mm) for thin sheet, 1.5 to 2.0 mm for most 3 to 10 mm plate, 2.5 mm and up for thick plate.
Stainless steel and aluminium, nitrogen or air
Use double layer nozzles. Larger bores are used on thicker material where more gas is needed.
Poor cut quality
Dross, a wandering kerf or bad piercing are often caused by a damaged or dirty nozzle. Fit a new nozzle of the same bore before changing other settings.
Height sensing faults
The nozzle is part of the capacitive height sensor. A worn or loose nozzle causes height alarms.
Found this part cheaper elsewhere? Send us the listing and we will beat it under our Price Beat Guarantee. Every order is also covered by our 30 day money back guarantee.
Heads that take the D32-H15-M14 standard nozzle on the D32-H12-M14 ceramic (Raytools 120274100B). Check the nozzle currently fitted if unsure.
Yes, if the machine runs a Raytools head that takes the D32 nozzle. The nozzle fits the head, not the machine, so check which head is fitted.
No. It is an aftermarket nozzle made to the same 32 x 15 mm, M14 dimensions. Raytools part numbers are listed so you can match your existing nozzle.
10, all the same layer and bore size you select. Nozzles are only sold in packs of 10.
Single layer for oxygen cutting of carbon steel. Double layer for nitrogen or air cutting of stainless steel and aluminium, where the inner cone stabilises the high pressure jet.
Use your machine's cutting chart for the material and thickness. As a guide, thin sheet runs 0.8 to 1.5 mm, mid plate 1.5 to 2.5 mm and thick plate 3.0 mm and up. Bigger bores pass more gas at lower velocity.
When the bore is damaged, out of round or coated in spatter that will not clean off, or when height sensing becomes unstable. Busy machines often change nozzles daily.
Yes. Shipping options and costs for your country are shown at checkout.
