Mitsubishi 092000-53616 is the six cylinder inline fuel injection pump: six delivery valve holders along the top, a red and black stop solenoid on the side, the governor housing at one end, the fuel feed pump and a black drive hub. It is used on Mitsubishi S6S engines. This aftermarket version is made to the same mounting and connections as the original, so it fits where the old one came off.
Sold as one unit. Check the number on your old part, or in the parts manual for your machine, before ordering.
Technical properties & sizes
Specifications
| Part Type |
Fuel Injection Pump |
| Replaces |
Mitsubishi 092000-53616 |
| Engine |
Mitsubishi S6S, S6S-DT |
| Cylinders |
6, inline pump |
| Fits |
Mitsubishi S6S and S6S-DT diesel engines in excavators, loaders and forklifts |
| Condition |
New, aftermarket |
| Stat. HS-Code |
841330 |
| Country of Manufacture |
China |
Compatibility
Mitsubishi machines
Mitsubishi S6S and S6S-DT diesel engines in excavators, loaders and forklifts
Check the part number on your old unit before ordering.
Part numbers
| Mitsubishi Part No.(SPM Part No.)
|
Fits |
|
092000-53616(SPM-HEP-5152)
|
Mitsubishi S6S and S6S-DT diesel engines in excavators, loaders and forklifts |
Applications & use cases
Hard starting and low power
A worn injection pump delivers less fuel at lower pressure: long cranking and weak power under load.
Smoke and uneven running
Uneven delivery between cylinders shows as smoke and rough running.
Fuel leaks
Leaks from the pump body or shaft seal mean it is time to replace it.
Fitting tips
Set the pump timing to the engine maker's figure, bleed the fuel system, and use clean fuel and new filters.
Price beat guarantee
We check what other aftermarket sellers charge for this same part. Their prices on the date we checked:
| Seller |
Price |
Checked |
| SINOCMP |
USD 1,169.00 |
2 Nov 2026 |
| eBay (3 aftermarket sellers) |
USD 1,278.13 to 1,297.68 |
2 Nov 2026 |
| Spare Part Mart |
USD 935.20 |
Today |
Our price of USD 935.20 is 20% to 28% less than these sellers.
Found this part cheaper somewhere else? Send us the listing and we will beat it by 5% under our Price Beat Guarantee. Every order is also covered by our 30 day money back guarantee.
Frequently asked questions
Will it fit my Mitsubishi S6S?
Yes, it was made for the Mitsubishi S6S, and 2 more listed under compatible equipment. Check the old fuel injection pump is marked 092000-53616 or one of the cross references, because makers change parts between serial ranges.
How often should I replace the fuel injection pump on my Mitsubishi S6S?
On the Mitsubishi S6S, often 5,000 to 10,000 hours with clean fluid, much less with dirt or air in the system. It is usually changed on condition, not by hours.
What are the signs the fuel injection pump needs replacing?
Leaks from the seal or weep hole, noise or whining, overheating, or falling pressure or flow under load.
Why did the old pump fail?
Most failures come from contamination, cavitation from a restricted inlet, or running low on fluid. Check the inlet and the fluid before fitting the new fuel injection pump.
What should I do with the gasket faces?
Clean them right back to metal and fit the new gasket or O-ring dry, unless the engine manual calls for sealant.
Is this a genuine Mitsubishi 092000-53616?
No. It is an aftermarket fuel injection pump made to replace the Mitsubishi 092000-53616. It is not made by the original manufacturer; the number only shows what it replaces.